Operators Manual539130211 - DCKC539130212 - DCRCModels:Please read these instructions carefully and makesure you understand them before using the mach
12ASSEMBLYFRONT WEIGHTS - KODIAKCAST COUNTERWEIGHTWEIGHT BAR HOLD DOWNFRONT WEIGHT BAR1. Remove mower foot plate and floor pan.2. Align weight bar to
13OPERATIONOperating the Collection System1. NEVER USE THE COLLECTION SYSTEMWITHOUT THE BLOWER ASSEMBLYAND HOSES SECURELY ATTACHED.2. Make sure hoses
14SERVICE AND MAINTENANCE Preventative Maintenance Schedule Item Before
15SERVICE AND MAINTENANCECaring For Hoses1. Inspect hoses before each use. If hoses haveexcessive wear, tears, or punctures, replaceimmediately.2. To
16SERVICE AND MAINTENANCE PROBLEM POSSIBLE CAUSE CORRECTION Loss of Vacuum. 1. Hose or ho
17PARTSILLUSTRATIONS
18CLAMSHELL ASSEMBLY12345678910REF.REF.3
19CLAMSHELL ASSEMBLY1.. 539 990629 ...2... HCS 3/8-16 X 2 1/4, GR52.. 539 200282 ...2... NUT, 3/8-16, HAM, NYLOC3.. 539 990122 ...3... WASHER, 3/8, SA
20CLAMSHELL REAR ASSEMBLY12345678910111213141516171819181010181012
21CLAMSHELL REAR ASSEMBLY1...539 117967 ...1... REAR FRAME2...539 119396 ...2... STRAP3...539 119367 ...1... HOOK LATCH4...539 119377 ...1... CLAMSHEL
4WARNING: Engine exhaust, some of its constituents, and certain vehicle components con-tain or emit chemicals known to the State of California to caus
22CLAMSHELL FRONT ASSEMBLY12345678910111213141617181920212223212526272824252015191823182318182316
23CLAMSHELL FRONT ASSEMBLY1...539 119410 ...1... FRONT FRAME2...539 119409 ...2... STRAP3...539 119368 ...2... STRAP4...539 117986 ...1... LIFT SHAFT5
24CLAMSHELL LINKAGE - RAM123456789101112131415161718510
25CLAMSHELL LINKAGE - RAM1...539 116443 ...1... BAR SLEEVE2...539 119372 ... 1... HINGE PIN3...539 114781 ... 1... BRACKET, MOUNT, LOWER4...539 114783
26CLAMSHELL LINKAGE - KODIAK123456789101213141516171819116310
27CLAMSHELL LINKAGE - KODIAK1...539 116443 ...1... BAR SLEEVE2...539 119372 ... 1... HINGE PIN3...539 115501 ...3...HAIR PIN COTTER, 1/8 DIA. X 1 3/44
WEIGHT KIT - RAM1... 539 111587 ... 1... CAST WEIGHT2...539 114898 ... 2... BRACKET, WEIGHT3.. 539 106492 ...4... HCS, 3/8-16 X 2 3/4, GR54...539 9911
WEIGHT KIT - KODIAK1... 539 111313 ...1... HOLD DOWN, WEIGHT BAR2.. 539 102049 ...2... CLEVIS PIN3.. 539 108096 ...2... SPRING RETAINER4...539 114858
5SAFETY RULESSafety Procedures1 - Training:• Read the Operator’s manual. If the operator(s)or mechanic(s) can not read English it is theowner’s respo
6SAFETY RULES3 - Operation• Never run an engine in an enclosed area.• Only operate in good light, keeping away fromholes and hidden hazards.• Slow dow
7ASSEMBLYAssembly InstructionsTools Required:RatchetTorque Wrench1/2" Wrench1/2" Socket9/16" Wrench9/16" Socket(2) 3/4" Wrenc
8ASSEMBLY10. Lift Clamshell assembly onto (539 114781)Mount Bracket, Lower. Position tubes onbottom of clamshell on out side of the tubeson (539 1147
9ASSEMBLYFIGURE 3KODIAK1. Remove clamshell from crate.2. Remove two 5/16 x 3/4 carriage bolts fromthe lower flange of the rear guard on themower.3. Pl
10ASSEMBLY5. Attach two (539 114812) Linkage, Supportto the clamshell assembly as shown in Fig-ure 6.6. Secure with two (539 100476) 5/8 hex jamnut an
11ASSEMBLYFRONT WEIGHTS - RAM1. Bolt cast weight and two weight brackets to-gether using four bolts (539 106492, 3/8 x 23/4”) and four nuts (539 97697
Comments to this Manuals